How To Adjust Trolling Motor Shaft Length?

Take a look at the mounting surface of the transom or bow. Fishing in rough water requires a waterline measurement of at least five feet. The measurement for steering a hand control motor should be added to the waterline. The appropriate trolly motor shaft length can be found by using the measurement and the tables.

Can you change shaft length on trolling motor?

If the shaft is too long, you can always adjust it with the depth collar adjustment found on nearly all trolly motor. You are out of luck if you choose a shaft that is too short.

Can you change the shaft length on a Minn Kota trolling motor?

It’s very easy to do, just remove the top cover, then there’s two wires going down the shaft to the motor, and then there’s a screw pinning the head to the shaft.

See also  What Trolling Motor Is Compatible With Lowrance?


 

How is shaft length measured on a trolling motor?

From the base of the motor head down to the top of the motor compartment, you can measure the shaft length.

Can you cut the shaft on a Terrova trolling motor?

Cut the amount in half. Don’t cut wires when you are cutting the shaft. I used a small metal pipe to slide down the shaft so I wouldn’t be able to cut the wires. The head should be put back on after the shaft is cut.

How far should a trolling motor be in the water?

6 inches of water above the blades is what the trolly motor’s ideal propeller should keep. The centerline of the motor and prop shaft should be at least 12 to 18 inches below the waterline.

Can you change the shaft on Minn Kota Terrova?

The lower unit at the factory has the Terrova shaft bonding to it. You purchase the shaft and midsection as a unit instead of just the shaft, and it can be replaced if wires are lenghtened.

Can you shorten shaft on Minn Kota Powerdrive?

Four phillips screws are used to remove the top cover and a machine screw is used to hold the head to the shaft. I wrapped the shaft in masking tape where I wanted it to be cut, then dropped down and put another wrap of tape on top of that.

How do you shorten the Minn Kota ultrex shaft?

Is it possible to shorten the shaft on an Ultrex? You need to be careful not to cut the wires and you need to drill the head screw holes again. If you do it yourself, you’ll void the warranty on the troll motor, so I recommend you go to an authorized service center.

See also  How To Mount Trolling Motor On Bow?

How does Minn Kota measure shaft length?

Take a look at the mounting surface of the transom or bow. Fishing in rough water requires a waterline measurement of at least five feet. The measurement for steering a hand control motor should be added to the waterline. The appropriate shaft length can be found by using the measurement and the tables.

How many pound trolling motor do I need?

The thrust needs to be at least 2 lbs. for every 100 lbs. of fully loaded boat weight. If the wind or current is a big factor in where you fish, you’ll want to increase your thrust.

How far below the boat should the prop be?

If you have a short shaft motor, the topmost part of the transom and the lowermost part of the boat should be about 15 to 16 inches. The length of the shaft is 20 to 21 inches.

Can you run a trolling motor out of the water?

It would take a long time to drain the battery and get the motor out of the water, if you ran it out for a short time. It’s not worth the risk to just drain the battery.

Will 2 trolling motors make you go faster?

The bow will be pushed higher in the air by two motors in the back, and the stern will dig in deeper to slow you down. If the boat is level in the water, it will be quicker.

How long should a trolling motor shaft be on a canoe?

The electric motor shaft is ideal for canoes. You can use the full thrust of the engine if the motor and propeller are far enough into the water. It will allow you to put the motor down deeper in the water if you get into choppy water.

See also  Best Trolling Motor For 16 Foot Jon Boat